Pool Equipment Repair in French Valley, CA

Fast, honest pool equipment repair for pumps, filters, salt systems, lights, valves, and automation. We diagnose the real problem, fix it right, and stand behind the work with a 100% satisfaction guarantee. Locally owned and fully insured.

We repair pumps, filters, salt systems, heaters, and automation from Pentair, Hayward, and Jandy, the three brands installed in most French Valley pools. That includes Pentair IntelliFlo and SuperFlo pumps, Hayward Super Pump and EcoStar, Jandy Stealth and ePump, plus Pentair Clean and Clean Plus, Hayward SwimClear, and Jandy DEV filters. Each brand builds its equipment a little differently, so the repair procedure, the diagnostic codes, and the replacement parts all vary.

We also service automation systems like Pentair IntelliTouch and EasyTouch, Hayward OmniLogic, and Jandy iAqualink, along with salt systems from all three manufacturers. When a control board fails or a relay sticks, we know how to read the error codes and find the exact component that went bad. We use genuine replacement parts so the repair holds up and your equipment runs the way the manufacturer intended.

A filter that leaks, will not hold pressure, or keeps clogging even after a full cleaning usually has a mechanical issue. The tank may be cracked, the clamp band may be worn, or the internal manifold may be broken. We handle pool filter repair on cartridge, DE, and sand filters from Pentair, Hayward, and Jandy so you do not have to find a second company to fix what the cleaning uncovered.

We replace O-rings, clamp bands, manifolds, and pressure gauges, and we fix air leaks that pull debris into the system. If the filter tank itself is cracked, we tell you honestly and give you a free written quote for a replacement. Many filter repairs add years of life to the unit, and we always let you know when a repair makes sense and when it does not.

When a filter is cracked beyond repair or too small for your pool, a replacement is the better investment. We size the new filter to your pool volume and pump flow so the water turns over efficiently and the filter does not work harder than it needs to. We install cartridge, DE, and sand filters from Pentair, Hayward, and Jandy.

We also handle the plumbing and valve connections so the new filter fits your existing pad without a full rebuild. After the installation, we start the system, check for leaks, verify the pressure, and log the clean baseline so we know when the next cleaning is due. We give a free written quote after seeing your situation, no pressure.

Automation systems run your pump, heater, lights, and cleaner on a schedule, so when the control panel fails your pool can turn fast. We troubleshoot Pentair IntelliTouch and EasyTouch, Hayward OmniLogic, and Jandy iAqualink systems. Common problems include dead displays, failed relays, communication errors between the panel and the equipment, and wiring issues from weather or age.

We read the error codes, test the relays and the transformer, and find the exact component that failed. In many cases a relay swap or a board repair gets the system running again without replacing the whole panel. If the board is beyond repair, we give you a free written quote for a replacement and reprogram it to match your schedule and equipment.

A salt cell that stops producing chlorine is one of the most common equipment problems we see. The cell plates may be scaled up, the cell may be at the end of its working life, or the control board may be sending the wrong voltage. We test the cell output, inspect the plates, and check the board so we know whether a cleaning fixes it or the cell needs replacing.

We repair salt systems from Pentair IntelliChlor, Hayward AquaRite, and Jandy AquaPure. If the cell is bad we replace it with the correct model for your system, and if the board has failed we repair or replace that instead. We also check the flow switch and the salt level so the whole system runs reliably after the repair. You can learn more on our salt cell cleaning page.

A salt system is more than the cell. It includes the control board, the flow switch, the wiring, and the sensors that tell the system when to run. When any of those parts fail, the system stops making chlorine and your pool can turn green in days. We diagnose the full salt system, not just the cell, so you do not replace a good part trying to fix a bad one.

We test the board output, inspect the flow switch, check the wiring connections, and read the error codes on the control panel. Whether the fix is a new flow switch, a board repair, or a full system replacement, we explain what we found and give you a free written quote before any work starts. We service Pentair, Hayward, and Jandy salt systems.

A dead pool light is usually a bad bulb, a failed gasket, or a corroded niche. We pull the fixture from the deck without draining the pool, test the bulb and the wiring, and replace the bulb and gasket so no water gets into the fixture. If the fixture is corroded beyond a bulb swap, we replace the whole light and reseal the niche.

We also repair and install LED pool lights from Pentair IntelliBrite, Hayward ColorLogic, and Jandy WaterColors. LED lights use less energy and last longer than incandescent bulbs, and we can often upgrade your old fixture to LED while we are there. We handle the wiring, the transformer, and the bonding so the light is safe and up to code.

Multiport valves leak through the waste port, push-pull valves stick open or closed, and diverter valves stop sealing over time. A leaking valve wastes water and throws off your circulation, and a stuck valve can keep water from reaching part of your pool. We rebuild valve assemblies with fresh gaskets, O-rings, and spider gaskets.

We service Pentair, Hayward, and Jandy valves, and we handle the plumbing connections so the repair fits your existing pad. If a valve is too far gone to rebuild, we replace it with the correct model and repipe the connections. We give a free written quote after seeing your situation, no pressure, so you know the full scope before we start.

A cracked skimmer, a broken weir door, or a leaking skimmer throat can all cause your pool to lose water or pull air into the pump. We repair skimmer cracks with the right epoxy or fiberglass patch, replace worn weir doors and baskets, and fix the skimmer faceplate so the skimmer pulls water the way it should.

If the skimmer is cracked through the throat or the body, we explain the repair options and give you a free written quote before any work starts. Some cracks can be patched and sealed, while others need a skimmer replacement. We tell you honestly which approach makes sense for your pool and your budget.

We always start with repair when it makes sense. A new motor, a seal kit, a relay swap, or a gasket replacement can add years to your equipment for a fraction of what a full replacement would cost. We diagnose the exact problem, explain what we found, and give you a free written quote for the repair before any work starts. If the fix is straightforward and the rest of the equipment is healthy, a repair is usually the right call.

When the equipment is too old, too damaged, or too small for your pool, a replacement is the smarter investment. We tell you honestly when that line has been crossed so you do not sink money into a repair that will not last. We give a free written quote after seeing your situation, no pressure, and we size any replacement to your pool so it runs efficiently for years.

Common Questions

Answers to the questions French Valley homeowners ask about pool equipment repair and getting the system back online.